![]() ![]() (These must be listed in your signature, or a link provided to a feedback thread listing these references)). Item Pictures: (List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. shipping include on east coast, $10 extra for out west. ![]() if you have something else in mind then just shoot it to me worst I can say is no Shipping and Miscellaneous Item Information: Will trade for a decent quality amp that does at least 1k 1 ohm. comes with a bass knob that displays voltage and has a clip light. Smash the competition without smashing your wallet. I've used it for about 3 weeks, haven't even gotten her warm yet. CT Sounds is a leading manufacturer of car amplifiers, subwoofers, speakers, and more. amazing output for such a tiny amp, this thing pushes 2 12s harder than my hifonics Brutus 1400.1 did 1ohm. This amp is incredible, 125x1 250x1 2ohms 500x1 it is underrated, rated on a 12.8v. Im using an audio technix AT 1200.1 which is the board as the ct 1400.1. Once again, don’t connect the last subwoofer in the series backto the amp, because the 1st sub already connects to the amp to complete thecircuit.CT sounds 500.1d AT Item(s) Description/Condition: It definitely sounds like CT sounds has a quality control issue with their big amps. Now, run a wire from the -terminal on the amplifier to the empty - terminal on the first sub.Connect the - on the 1st sub (the one that’s connected to the amp, notthe one that’s bridged) to the empty - terminal on the 2nd subwoofer.Connect the same - on the 2nd subwoofer to the empty - on thethird subwoofer, and do the same to connect the - on the 3rd sub to the -on the 4th sub. Do not connect the4th sub back to the amplifier, the first sub is already connected to the amp. Car audio amplifier with 2000 watts RMS power at 1-ohm load (14.4v) 1200 watts RMS at 2-ohm load (14. Next, connect the same + wire from the second sub to the empty + terminal on the 3rd sub, and then connect the + on the 3rd sub to the + on the 4th sub. ![]() Next, you’ll connect the +from the amp to the empty + on the first subwoofer (not the + that is already bridged with the - on the same sub.) Run another wire from the +on the first sub (the one that’s also connected to the amp) and connect that to the empty + on the second sub. This leaves both posts empty on the amp still, and each sub with one empty + post and one empty - post. Your amp has a + and a -, and each sub has two +’s and two -’s.Įach of the subs should have a bridge wire to connect one of the +’s with one of the -’s on the same sub. If you have four subs, each one with dual voice coils at 2 ohms, and a mono amp under a 1-ohm load, here’s an explanation of how to wire that… If you have two2-ohm subwoofers, you would divide 2 by 2 and get an impedance of 1 ohm. The formula for calculating the impedance in parallel wiring is to add together the total ohms from each subwoofer, and then divide them by the number of subwoofers. Unlike in series, where positives connect to negatives. Parallel Wiring: When you’re wiring in parallel, the positive wires connect to the positive posts, and the negative wires connect to the wireless posts.Four 2-ohm speakers wired in parallel would give you an impedance of 8. Wiring in Series: When you’re wiring multiple subwoofers in series, you’re connecting the positives from one subwoofer to the negatives on the next one.The formula for calculating the total ohm load when wiring in series is to simply add the ohms from each speaker together.Paul Kim at M & Tech probably wants his money back cthedinger, why dont you come try to lie your way out of. So much for the lie that you made 'mistakes' He never paid back the 250,000 he stiffed a supplier out of. The thing to do is call the dealer you bought it from or, contact CT Sounds directly if you didnt buy it from a dealer. This also applies to subwoofers with dual voice coils. So apparently Coleman is still pulling the same as 4-5 years ago. The amp has a one year no fault warranty so at the most, it would cost the exchange fee and shipping to have it replaced. The 1-ohm stable monoblock amplifier features a Low Pass Filter (LPF), Subsonic Filter, and Bass Boost so you can get the exact sound you are looking for out of your amplifier. The formula to calculate the impedance will depend on whether you’re wiring in series or in parallel. The CT Sounds CT-1000.1D is a compact 1000 watt class d monoblock car subwoofer amplifier. First things first, you’ll need to determine how many subwoofers you plan on wiring into your amp, and what their requirements are, and what your amplifier can output in terms of power. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |